Bootstrapping (electronics)
From Wikipedia, the free encyclopedia
| This article is orphaned as few or no other articles link to it. Please help introduce links in articles on related topics. (September 2006) |
| This article does not cite any references or sources. (September 2006) Please help improve this article by adding citations to reliable sources. Unverifiable material may be challenged and removed. |
The term bootstrap has a number of meanings in electronics.
Contents |
[edit] Electronics
In classical analog designs, a bootstrap circuit is an arrangement of components used to boost the input impedance of a circuit by using a small amount of positive feedback, usually over two stages. This was often necessary in the early days of bipolar transistors, which inherently have quite a low input impedance. The need for such arrangements has largely been alleviated by the use of modern field effect transistor designs, except when ultra-high input impedances are required. Note that because the feedback is positive, such circuits usually suffer from poor stability and noise performance compared to ones that don't bootstrap.
Bootstrapping comes from the stories about Baron von Münchausen who got stuck in quicksand and lifted himself by grabbing his bootstraps; that the output transistor "lifts its own control voltage" is what is meant with "bootstrap" functionality.
N-MOSFET/IGBT needs a positive source-gate voltage. If you cost reduce by using only N-channel MOSFET/IGBT (there are other benefits as well) you will need a voltage higher than the power rail supply at (V+) to saturate the transistor and thus avoid significant heat loss.
By connecting a capacitor between the output (drain) and cathode of a diode and connect the anode to (V+) the voltage will rise above (V+) when the transistor between (V+) and output "lifts" the voltage.
MOSFET/IGBT is a voltage controlled device and won't in theory have any gate current. This makes it possible to utilize the charge inside the capacitor for control purposes. However, eventually the capacitor will lose its charge (due gate current), so this scheme is only used where there is a steady pulse is present.
[edit] Amplifiers
AC amplifiers can use bootstrapping to increase output swing. A capacitor (usually referred as bootstrap capacitor) is connected from the output of the amplifier to the bias circuit, providing bias voltages that exceed the power supply voltage. Emitter followers can provide rail-to-rail output in this way, which is a common technique in class AB audio amplifiers.
[edit] Computer Systems
Another meaning is in connection with the booting process of a computer or other complex system, where the underlying electronics must arrange for the orderly startup of the CPU and related electronics components. This is done long before the CPU is in a state where it can begin to execute software. Nowadays the bootstrap is coordinated by special integrated circuits that monitor the raw power supply and provide the relevant signals to enable the CPU and other chips accordingly.
[edit] Automobiles
In a typical car alternator, a DC field current is required before the device can produce any output. Once running, a small portion of the output is fed back to keep the field alive — this can be seen as a form of bootstrapping. The initial priming current is usually obtained from the vehicle's battery — if the battery is totally flat the alternator won't produce any output voltage to spark the plugs or recharge the battery (by push starting for example) since it will be unable to bootstrap itself. However, in practice, a battery will usually have enough residual charge to avoid this.
[edit] Power Grids
In reference to a regional or national power grid, bootstrapping refers to the process of restarting generating stations and restoring power to the grid after a large-scale power outage or disaster. This is also referred to as cold starting or black starting. The process is required for reasons not dissimilar to the automobile case above: many power stations have AC generators which do not contain permanent magnets, and are incapable of starting to produce electricity unless they are fed some from an outside source to energize the coils and produce a magnetic field. Once running, they use their own output power for this purpose and are self-sustaining. Some power plants are designated within the grid as being capable of a cold start (either because they have main generators which contain magnets, or have smaller auxiliary generators which do and which are capable of bringing the main ones up), and these plants are brought on-line first, and their power output directed across the grid to other plants and used to start them. In this way, generating stations across the network can be progressively brought back up.de:Bootstrapping (Elektrotechnik)
